Skip to content

How To Turn A Corner With A DownSpot – [Amazing Technique]

Rainfall is a common and essential part of our environmental system, and this is hard to find a person who doesn’t like rain. But when it becomes an issue of protecting our home and roof, rain can be problematic sometimes. In that case, keeping our home safe from moisture damage and the threat of flooding is an essential matter of concern for us.

So, how to turn a corner with a downspot? And that’s why downspouts or rainwater leaders can be so handy. It’s an essential component of any gutter or drainage system that helps control soil erosion and damage to the building foundation.

How To Turn A Corner With A DownSpot

How To Turn A Corner With A DownSpot – You Should Be Know 

How To Turn A Corner With A DownSpot - You Should Be Know 

If we look at drainage systems, we will see that they usually have a slight downward pitch toward the corners of the home, which direct rainwater or for say snowmelt to flow “downhill” through the gutters and into the downspouts.

The downspout apparatus is connected at the top to a hole in the gutter channel and it runs vertically along the side of our residence. So the fact is that gutters catch rainwater as it descends from our roof and encourages its flow to the downspout so that it can be drained.

An underground downspout keeps rainwater away from our home, which protects its foundation by keeping the basement dry and moisture-free. So in a sentence, we can say that downspouts are specially designed equipment which is usually vertical and pipe-like and is attached to gutters installed along the sides of the home to redirect water leading it away from our home towards a selected drainage area in a very systematic way.

The thing that comes next into consideration is how to install and maintain downspout(s) correctly. The first thing important is not to skimp on the matter of quantity. The required amount of downspouts must be ensured to be attached to the roof’s gutter system.

It will maximize the efficiency level of the drainage system and also will be very cost-effective because fewer downspouts than the satisfactory numbers along the house exterior can lead to water back-up during heavy storms and rainfall and thus can create bottlenecks nullifying the purpose of the gutters and downspouts.

It is also essential to ensure that the downspout bases must be far enough away from the residence so that they can work properly. The ends of downspouts should be angled strategically and positioned towards the drainage areas so that water makes very little or no contact with the edge of the house foundation.

Though basic guidelines are available online, it is wise to help a professional or expert while installing downspout(s) if self-experience is lacking. It is necessary to make a list of the things that will be required and have them available before start working on it. There is no fixed protocol, but here are some steps showing how the procedure can be done:

  • The first task is to dug a trench the measurement of which will be eight to 10 feet in length, around 12 to 14 inches in depth and about 6 inches in width for each of the downspouts on the house. While doing so it is to keep in mind that the depth of the trench has to be dropped to at least 1/8-inch per foot which will ensure the proper movement of water away from the house.
  • Next, a piece of 450 angle joint (PVC is recommended) is to be connected to one end of a piece of sewer pipe measuring 8-10 feet in length with a diameter of 4 inches. Then by using PVC glue, fittings for these two pieces is done. To do it properly, it is better to rotate them slightly at the time of gluing.
  • After that, the angle fitting is to be drifted with a downspout filter. The setting has to be done in such a manner so that the filter is slightly above the ground. A mark is to be pointed on the downspout where it is needed to be cut. For cutting, a pair of metal snips or any kind of scissor can be used.
  • The downspout filter is to be attached to the downspout. The filter should be connected with any fasteners like screws. Next, the 450 angle joint is to be slid onto the bottom of the filter using PVC glue to secure it. At this point, the sewer pipe should be in a horizontal position to the trench and if required, some dirt can also be pushed beneath the pipe and angle joint for additional support.
  • Next, a two to three feet deep hole is dug under the sewer pipe’s end. A bag of sand is better to pour into the hole. This is expected to provide sewerage for the water that runs off the roof portion of the house.
  • After that, a T-connector (PVC) is moved along the open end of the sewer pipe in such a way so that it goes up and down on the mentioned pipe. Then a filter is to be fastened on the top surface of the T-connector. As these connectors are going underground, that is why gluing is not needed in this case.
  • The next task is to calibrate the T-connector to mount the upper part with the drain with the ground. The rainfall-runoff from the downspouts will first fill the hole that is packed with sand. Any surplus of this will flow up out of the pipe and on the top of the basement. The drain can be opened to clean out whenever necessary.
  • Finally, the trench has to be filled with packing dirt around the pipe, and the surface is expected to be smooth.

To conclude, downspouts are essential and crucial tools for our houses. A house without gutters and downspouts is much more vulnerable to waterlogging and corrosion damage than a house with a designed drainage system.

It is mandatory to fulfill the criteria to make it work properly. After installing, thorough maintenance is also essential as it will help to keep the downspouts in our houses functional over the years.

Proper sealing, appropriate filtering, keeping leaves and debris out as much as possible, regular cleaning, and professional replacements of the drainage system in cases of severe damage will help to protect our beloved home in the long run and prevent us from many associated problems.

Conclusion

I hope now you know about how to turn a corner with a downSpot.

Leave a Reply

Your email address will not be published. Required fields are marked *