Skip to content

How To Run Romex In The Attic? Step-By-Step Process

A well-designed attic can become a valuable asset for a home when used correctly. Running cables through the attic is commonplace and remarkably safe. Almost everyone now uses their attic to establish a hassle-free connection.

It is possible to run electrical and internet cables through the attic. So, how to run romex in the attic? Romex cable is commonly used for providing power connection, which is easy to run in the attic. They are strong and long-lasting, so these are perfect for mounting in attics. You can do this cable management yourself. You need the experience to work with electrical equipment. If so, let’s start working.

How To Run Romex In The Attic

Safeguarding

Safeguarding

As a first step, we must ensure security. As the attic is a very tight space and there is a lot of dust, you should wear eyeglasses and a mask before entering. You must use a ladder if you do not have a dedicated staircase for climbing the attic.

Our preference would be to utilize an A-shaped ladder. There are usually no additional lighting systems in attics, so arrange for adequate lighting before climbing upstairs. Furthermore, you can use a head torch or a regular torch.

Go up to the attic to see what’s up there. Your weight may exceed the capacity of the attic since it is made of very light material. You will require assistance if you have to walk there. You can use a metal frame or a few planks for support. It will help you spread your weight out over many areas.

In the case of cables already in the attic, you must turn them off. Nevertheless, make sure the electronic tester is connected to the power source if you want to be sure. Keep the main switch off if necessary.

Taking Measurements

 

Calculate the distance between each room you wish to connect. Take measurements with a tape measure. You may want to write down or remember the size that you got.

If you want to run the wires to another room through a wall, it is much easier. As such, mark the location in the attic where the wire will be. It will be a little challenging to get it down through fishing wire. Mark, however, two places where the fishing wire is needed.

The Equipment

The Equipment

You need first to cut the Romex Cable that you will use. If possible, extend a Romex cable at least one meter beyond the distance you wrote or remembered. To complete the process, you will need some tools. Here are the tools:

  1. Drilling machine
  2. An arm hammer
  3. Zip tie
  4. Junction box
  5. Ceiling-cutting blade
  6. Staples
  7. Multi-function electronic tester
  8. Screwdriver.

Take everything and head upstairs.

Preparing And Installing

Preparing And Installing

For connections through the walls, drill holes where the previously marked points are located. Make the holes a little wider than the length of the cable. As long as there is only one cable, our recommendation is to drill the attic.

In contrast, if you plan on connecting a fishing cable, drilling a hole is not enough. It is not sufficient to use a single hole for multiple cables. Hence, junction boxes are necessary. Make a pencil mark on the roof according to how big the junction box will be. With a blade, cut the material according to its size. You can cut a box for each place you need to attach more than one room by cutting a space for it.

The Cable Connection

The Cable Connection

In the attic, there are several ways to provide cable connections. These are a few easy and suitable methods.

The Surface Of The Attic

The Surface Of The Attic

Cables are typically installed above the attic’s surface. Run one side of the cable through the junction box. Connect the other side to the room below We also do various things in the attic sometimes. The cable becomes less durable as a result of walking on it. Electric cables can pose a danger to us if we walk on them.

The Ceiling

The Ceiling

You can attach a Romex cable to the ceiling. Compared to the surface, it is more secure because our bodies do not touch the ceiling. One disadvantage is that it uses more cable than it needs. In terms of durability, however, it’s not an issue. It is not enough to hang the cables on the ceiling, which will cause them to move sideways.

Therefore, the cables must be stapled to the ceiling. It would help if you held the cables against the ceiling with your hands. Attach the staple to the cable with a hammer. Staples usually line up four feet apart. You can staple more if it takes more. Attach the Romex from the ceiling to the attic using studs or joists at the ends. Staple the cables to the joists.

Throughout The Joists

Throughout The Joists

The most sustainable method would be to run the Romex cable through the joists of the attic. The process is easy, and once you know how to do it, you don’t have to worry about it.

Due to the cable having to go through the joists, you have to drill holes in them. Drill a hole in the joist carefully. Try to make a hole in the center. A hole in the side can damage the joist.

Now for the wire. Insert it through the joist and move it from one end to the other. There’s no need for a separate staple. Although, there is a significant downside. If you use more than two cables, you will not pass the cable through the joist. You’ll have to punch a huge hole in it, causing the joist to collapse. If you want to run one or two Romex Cable Attics, you can use Joists.

J Hook

J Hook

If you connect many cables to the attic, neither the joists nor the ceiling will work. Then you will need J Hook. J Hook looks like the English alphabet ‘J. Attach the hook to the ceiling, joist, or studs using screws. On top of that, you have to hang the wires.

If you use fewer than five cables, you must tie them together. Tie them with zip ties. From one end of the serial attic to the other, attach the J hooks. Hook up the cables.

When you use 10 cables or more, loop 5 cables together and attach them with zip ties, a common j hook has a circular edge for hanging. Dual or triple j hooks are available, however. Buy a double or triple j hook if you have a lot of cables. Each hook should now hold five of them.

Using j hook is the most professional choice. It is easy to customize on-demand and is highly durable. When using a single cable, however, there is no need for J hooks.

The Final Touch

We’re done with the attic. Your next task will be to leave everything upstairs and come down to the room with the tools. Afterward, connect the cables to the different locations as needed. When you use a junction box, you can see a large hole in the roof.

Attach the junction box hood there with screws. If you make a mistake in connecting, ask a professional for help without wasting time. I hope now you know how to run romex in the attic.

Leave a Reply

Your email address will not be published. Required fields are marked *